How to Install the Quick-Release Push-Button Lock to your Window Guard

Attach typically the Strike Pin to your window guard

The particular Strike Pin (3) should be permanently installed on or close to the outer sheet metal framing in the windowpane guard -referred to from now on as WG- on the side of the WG’s “door” opposite of the hinge, close to the middle (the same place in which a doorknob is situated over a door). That should extend external from the WOHNGRUPPE toward the wall membrane, so that this will later fall into the Lock Box tip-first if closed.

IMPORTANT: Typically the Strike Pin ought to point straight as possible, ie not directing slightly up, along, to the kept, or to the right. The straighter it is, the smoother the operation later.

The rear of the Affect Pin has posts to get a 1/4″ sl?, so a standard way of affixing the strike flag to your WG is by first fixing a 1/4″ sl? it, then screwing the Strike Green into that. Still, a person want people having the capacity to simply unscrew the bolt by the outside, it is therefore important that you permanently fix it to be able to the WG. It is most often completed by spot welding the attached Affect Pin in place, yet if a welder isn’t handy, any way the bolt can be made unturnable works, such as using one-way bolts.

Support the Window Guard

If it isn’t previously, it’s time to be able to mount the WOHNGRUPPE on your windows. Attach the Lock Box (1) for the end of your own pin so of which it locks in position. If it will not, be sure it will be unlocked first simply by pushing the final of the Push Rod (2) into typically the smaller hole of the Lock Package first. This Lock Package will be attached to the outer wall of your building, so that you want to install the WG in the position where the Secure Box can be mounted using the top rated and bottom twist holes, and cannot be pryed off (such as when it sits off the edge of your windowpane frame).

The other issue to keep inside mind this is that will there will always be an approximately 1/2″ hole drilled through your wall positioned in the midsection of the Locking mechanism Box, and on the particular inside of the building, a a single 5/8″ diameter Flange will mount in order to the wall close to that hole. When you put way up the WG, an individual want the Locking mechanism Box to become close to the window starting, but far enough to allow for this 1/2″ hole to become drilled with the wall structure, and hopefully end up being clear of any kind of inner wall items in the way (like inside framing) for a 1 5/8″ diameter all-around the hole middle.

Mark your hole

With the Strike Pin attached to be able to your WG, plus the WG linked to your constructing, the remaining is relatively easy!

Now we want to mark where the hole will end up being drilled through the particular wall in order that it suits the small pit on the back of the Fasten Box. First, force the Push Rod (2) in the Locking mechanism Box hole so it releases through the Strike Pin, plus remove it. Place the Cardboard Slip (4) all the way up onto the Strike Pin, and cut-off typically the end with the knife so typically the cardboard only hardly extends beyond typically the Strike Pin. Close up the WG front door slowly till the round of cardboard complies with the wall, and then use a pencil to draw some sort of circle where that lands.

Drill

Formally a 3/8″ exercise bit will turn out to be just right for typically the Push Rod to fit into, although I recommend a new 1/2″ bit, which often leaves more room for error, and is covered upward just fine. While using circle you only marked, drill a hole straight by means of your building wall until you break the rules of lack of.

At this specific point, reattach typically the Lock Box towards the WG and carry it closed. Somebody from the within should be in a position to put their very own eye through the newly drilled hole in addition to see the TOTAL small hole of the Lock Pack. If it will be partially covered, punch out your hole until which clear way to it.

push button enclosure Install the Lock Container

If it basically already, reattach the particular Lock Box for the WG and hold it closed. Tag the upper and lower holes involving the Lock Field with your reliable pencil, then wide open the WG and even drill them together with the drill tad (NOT the large one! ) that will matches the anchoring screws you’re going to use to support the Lock Field, which don’t include the kit. These kinds of screws should be between 1/4″ plus 3/8″, and should be about 2″ to 3″ extended.

With your two holes drilled previously mentioned and below your current BIG one, take away the Lock Box in the WG (you recognize how by now, proper? ), place it on the walls, and mount that with your many of the. Screw them inside until they’re comfortable, smaller completely tighten up at this time.

Align typically the Lock Box

Little by little close the WOHNGEMEINSCHAFT communicate mounted Secure Box, being very careful Never to lock this in place. What’s that will? You say the particular Strike Pin basically lining up? Require a chill pill, I’m getting there.

With the hammer, smack the Lock Box sufficient to move this in the direction it needs to look. In the event that it won’t budge, you screwed it in a bit too tight in addition to will need to loosen it. Any time it is lined up properly, you may well lock it throughout place to make certain this works. It can be unlocked, of course, by keeping the Push Pole (2) through the hole in typically the wall until it launches. Note that you may need to “fish” around for the smaller hole within the Lock Box to push it in just about all the way.

When everything is lined up, tighten the particular Lock Box screws all the approach. If everything is definitely well aligned, typically the Push Rod need to easily open the WG as well as the WG should easily secure in place. Even with the screws are tightened, you may be in a position to make use of the hammer for final adjustments.

Leave a Reply

Your email address will not be published. Required fields are marked *